24-Hours To Improve Door Lock Change
How to Do a Door Lock Change
Change your door lock is a simple and inexpensive way to increase the security of your home. This isn't for all. It requires a certain amount of patience and expertise.
You need to replace the cylinder that is located within the knob's body. The cylinder recognizes the key when it's put into the lock.
The old lock can be removed
The first step to replace the door lock is to take out the old lock. It's a straightforward process, however you must keep a few things in your mind. Make sure that the new lock fits your door. This will ensure that it fits snugly and doesn't leave a gap around the deadbolt plug or latch.
Once you have removed the latch plate look for two bolts or screws on the inside of the casing, which hold the casing and the two halves of the lock together. Remove these screws with a screwdriver before removing the lock out of the door. If you have a mortise lock, there may be a set screw at the base of the handle that holds it to the spindle. Use a screwdriver to unscrew this screw, then pull out the doorknobs.
Remove the deadbolt as well as the latch plug from your door jamb. Install your new lock. If you are replacing a mortise lock you should also determine the distance between the lock case and the edge of your door to ensure that your new lock will fit.
It is possible to replace your lock for various reasons, such as when you suspect that someone else holds the key or if you've new roommates. You could save money if you take the lock off yourself instead of paying for a professional. The process is easier than many people think and can be completed in a few minutes.
Remove the trim and handle from your door. With a flat screwdriver, take off the trim. You will be able twist off most of it, and in certain cases the handles could come off entirely. The next step is to look for a pinhole on the inside of the handle and insert a straightened clip into it. This will activate the release mechanism and allow you to take the handle from the door. Then, look for another small tab that is located inside of the lock, and press it with a screwdriver that is flat. Once the spindle has been removed, you can remove the housing and cylinder.
Making a decision on a new locking system
You have many options when it comes time to pick the right lock. Consider the different types of locks and choose one that fits the design of your door. Consider the backset (the distance between the door's edge and the center of the lock hole) and the cross bore (small hole in the frame of the door frame). Choose a lock that fits the door's thickness and swing.
The majority of door locks are assessed by BHMA and the American National Standards Institute to give you an idea of how well they stand up to use and how difficult to disable or pick. A grade 3 lock could be a good choice for a tranquil suburban apartment complex, whereas the grade 1 lock may stand up to the traffic that is frequented by a retail storefront on a busy street.
Most smart door locks require digital code to open. If you are worried about hacking or other security concerns, speak to a professional locksmith.
Replace the cylinder
You can easily replace damaged or broken door lock cylinder with an easy DIY project. The key is to choose the right cylinder, and follow the instructions that come with it. The first step is to remove the knob or handle, should there be one and then remove the trim around the base of the lock cylinder by using the aid of a screwdriver. Once the trim is removed, you will be able to access the screws that keep the cylinder in place and remove them with a flathead screwdriver. The cylinder is then gently removed away from the door.
Before installing the new cylinder, make sure that it's the right length for the door you are using. Find the distance from the center to the right and left sides of the cylinder using an instrument. Purchase a new cylinder which has the same measurements. This will prevent cylinders from snapping when the door is kicked or the key gets stuck inside.
Once you have a suitable replacement cylinder, put it in the door and turn the key. blog will align the cylinder with the carriage that is usually located on the outside of your lock. You can then loosen the set screws that should be a couple of turns in the head. If there is a screw located on the exterior of the case that is holding the door, you'll need to loosen it.
After you have removed the lock cylinder, you can replace it with the new lock by slipping the new cylinder into the case and tightening the set screw. Installing the part that connects a cylinder with the stem of a lock indicator is also important. This can be done by pulling three small tabs on the back of the cylindrical with needle-nosed pliers. Attach the smaller bracket to the cylinder's back. You must then install the latch plate and strike plate, along with the retaining rings connected to the top of the lock the cylinder.
Installing the new lock
If you're replacing a previous lock, start by measuring the width of your door. The majority of residential locksets have a thickness of 1 3/8 to 1 3/4 inches. If your door is thicker than 1 3/8 to 1 3/4 inches, you'll need a thicker door kit. This would include longer screws and either a longer spindle extension or tail piece for door knobs.
The majority of locks come with a detailed instruction booklet to help you install the new hardware. Before you begin, go through the instructions to make sure you've followed the steps. The booklet will also give you an idea of the degree of skill required to accomplish the task. If you're changing a lock for the first time, you might want to ask an experienced friend for assistance.
It's a great idea to seal the openings of the old hardware before installing the new lock. This will stop the screws from slipping out of the holes and safeguard any tile you may have put in the area. It will also protect your tiles from any damage caused by rust, dirt and grime. SECURAM Touch comes with a strip of painter's tape designed to be used to protect your painter's tape, but you can also use gaffer's tape as well as masking tape if you have it available.
Once you've removed the screws holding the inside of the lock section to the outside side then pull it out straight away. This should be done swiftly to avoid the lock from accidentally closing and harming the mechanism.
Fit the new latch bolt in the upper cross bore of the new lock, if it has one. Make sure you put it in the proper location, which is marked by an arrow. Then, screw the latch plate onto the bolt.
Attach the deadbolt to the door jamb. Test the deadbolt by throwing it a few times to ensure that it extends all the way into the strike plate and is secure. Follow the instructions that come with your electronic smart lock to program it. This involves downloading an application and entering your email address, confirming your identity, and accessing the wireless network to connect your device.